United StatesChange
CADDY

CADDY CAT HP J-Hook Tree, Flange Mount

Features

  • Easy installation to beam flanges
  • Provides optimal support for high-performance data cable, up to and including Cat 5e, Cat 6, Cat 6A, Cat 7 and fibre optic
  • Ready to use out of the box, saving installation time and labor
  • Requires no screws, rivets or special tools for assembly
  • Single- or double-sided tree configurations provide multiple J-Hooks with one structural attachment
  • Provides superior fill capacity and load rating over most other non-continuous cable support alternatives
  • Complies with EN 50174-2
  • Meets ISO®/IEC 14763-2, ANSI®/TIA 568 and ANSI®/TIA 569

Specifications

Material: Steel
Finish: Pregalvanized
Type: Double Sided
Part Number DiameterØ Tiers Flange ThicknessFT HeightH WidthW A B TorqueTQ Static LoadF
CAT32HPDFM2 2" 2 13/16" Max 10 1/4" 5 13/16" 1 1/8" 2" 5 ft lb 240 lb
CAT32HPDFM3 2" 3 13/16" Max 15 1/4" 5 13/16" 1 1/8" 2" 8 ft lb 360 lb
CAT32HPDFM4 2" 4 13/16" Max 20 1/4" 5 13/16" 1 1/8" 2" 8 ft lb 480 lb
CAT64HPDFM2 4" 2 13/16" Max 15 1/4" 10" 1 1/8" 2" 5 ft lb 240 lb
CAT64HPDFM3 4" 3 13/16" Max 22 3/4" 10" 1 1/8" 2" 8 ft lb 360 lb
CAT64HPDFM4 4" 4 13/16" Max 30 1/4" 10" 1 1/8" 2" 8 ft lb 480 lb
Type: Single Sided
Part Number DiameterØ Tiers Flange ThicknessFT HeightH WidthW A B TorqueTQ Static LoadF
CAT32HPSFM2 2" 2 13/16" Max 10 1/4" 3 5/16" 1 1/8" 2" 5 ft lb 120 lb
CAT32HPSFM3 2" 3 13/16" Max 15 1/4" 3 5/16" 1 1/8" 2" 5 ft lb 180 lb
CAT32HPSFM4 2" 4 13/16" Max 30 1/4" 3 5/16" 1 1/8" 2" 5 ft lb 240 lb
CAT64HPSFM2 4" 2 13/16" Max 15 1/4" 5 7/16" 1 1/8" 2" 5 ft lb 120 lb
CAT64HPSFM3 4" 3 13/16" Max 22 3/4" 5 7/16" 1 1/8" 2" 5 ft lb 180 lb
CAT64HPSFM4 4" 4 13/16" Max 30 1/4" 5 7/16" 1 1/8" 2" 5 ft lb 240 lb
Static loads represent maximum load limit of J-Hook tree. Static load limit of each J-Hook is 60 lb (270 N).
Setscrew must be tightened and torqued onto the sloped side of the I-beam.
Non-continuous supports may not exceed spacing of 5' (1.5 m) per TIA 569-C.9.7 and EN 50174-2.
Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added.

Pentair, CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.

ANSI is a registered trademark of American National Standards Institute.
ISO is a registered trademark of International Organization for Standardization.

Applications

Video