United StatesChange
CADDY

630 Pipe Saddle for 1" Insulation

Features

  • Designed for high temperature service or where heat losses are to be kept at a minimum and to protect insulation against damage at the point of support
  • Conforms with Federal Specification WW-H-171 (Type 40A or 40B), Manufacturers Standardization Society ANSI®/MSS-SP-58 (Type 39)

Specifications

Material: Steel
Finish: Plain
Part Number Pipe Size LengthL Insulation Thickness
6300150PL 3/4" – 1 1/2" 12" 1"
6300350PL 2" – 3 1/2" 12" 1"
6300500PL 4" – 5" 12" 1"
6300600PL 6" 12" 1"
6300800PL 8" 12" 1"
Part Number Pipe Size Cover Thickness Size of Pipe Roll for Model # Center Line of Pipe to Outside of Saddle Center Line of Pipe to Center Line of Roll for Model # Static Load
F
605, 615 610 617, 619 605, 615 610 617, 619
6300150PL 3/4" 7/8" 2 1/2" 2 1/2" 2" - 3 1/2" 1 3/4" 2 3/16" 2 1/4" 2 3/8" 1,200 lb
1" 1 1/16" 2 1/2" 3" 2" - 3 1/2" 1 15/16" 2 7/16" 2 3/8" 3" 1,200 lb
1 1/4" 7/8" 2 1/2" 3" 2" - 3 1/2" 2 1/8" 2 11/16" 2 5/8" 2 3/4" 1,200 lb
1 1/2" 1" 3" 3 1/2" 2" - 3 1/2" 2 1/4" 2 3/4" 2 3/4" 2 1/4" 1,200 lb
6300350PL 2" 1 1/16" 3 1/2" 4" 2" - 3 1/2" 2 7/16" 3 1/16" 3 1/16" 3" 1,200 lb
2 1/2" 1 1/16" 3 1/2" 5" 2" - 3 1/2" 2 3/4" 3 5/16" 3 5/16" 3 3/8" 1,200 lb
3" 1" 4" 5" 2" - 3 1/2" 3 1/16" 3 5/8" 3 5/8" 3 11/16" 1,200 lb
3 1/2" 1 1/4" 5" 6" 4" - 6" 3 3/8" 4 1/16" 4 1/16" 4" 1,200 lb
6300500PL 4" 1 1/16" 5" 6" 4" - 6" 3 7/16" 4 1/8" 4 1/8" 4 1/16" 1,800 lb
5" 1" 6" 8" 4" - 6" 4 1/16" 4 3/4" 4 3/4" 4 11/16" 1,800 lb
6300600PL 6" 1" 8" 8" 4" - 6" 4 9/16" 5 3/8" 5 3/8" 5 1/4" 1,800 lb
6300800PL 8" 1 1/2" 10" 12" 8" - 10" 6" 7 1/16" 7 1/16" 7 1/16" 1,800 lb
Maximum recommended loads are applicable only when the saddle is used on a flat bearing surface and tack welded to the pipe. When a saddle is used with a pipe roll, the maximum load given for the pipe roll applies to the saddle.
Install in accordance with applicable code.

Pentair, CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.

ANSI is a registered trademark of American National Standards Institute.