United StatesChange
CADDY

634 Pipe Saddle for 3" Insulation

Features

  • Designed for high temperature service or where heat losses are to be kept at a minimum and to protect insulation against damage at the point of support
  • Conforms with Federal Specification WW-H-171 (Type 40A or 40B), Manufacturers Standardization Society ANSI®/MSS-SP-58 (Type 39)

Specifications

Material: Steel
Finish: Plain
Part Number Pipe Size LengthL Insulation Thickness
6340200PL 2" 12" 3"
6340250PL 2 1/2" 12" 3"
6340300PL 3" 12" 3"
6340350PL 3 1/2" 12" 3"
6340500PL 4" – 5" 12" 3"
6340800PL 6" – 8" 12" 3"
6341000PL 10" 12" 3"
6341200PL 12" 12" 3"
6341400PL 14" 12" 3"
6341600PL 16" 12" 3"
6341800PL 18" 12" 3"
6342000PL 20" 12" 3"
6342400PL 24" 12" 3"
Part Number Pipe Size Cover Thickness Size of Pipe Roll for Model # Center Line of Pipe to Outside of Saddle Center Line of Pipe to Center Line of Roll for Model # Static Load
605, 615 610 617, 619 605, 615 610 617, 619
6340200PL 2" 3 1/8" 8" 8" 4" - 6" 4 11/16" 5 1/2" 5 1/2" 5 1/2" 1,800 lb
6340250PL 2 1/2" 3 3/8" 8" 10" 4" - 6" 4 15/16" 5 11/16" 5 13/16" 5 9/16" 1,800 lb
6340300PL 3" 3 1/16" 8" 10" 8" - 10" 5" 5 15/16" 5 15/16" 6" 1,800 lb
6340350PL 3 1/2" 3 5/16" 10" 10" 8" - 10" 5 1/2" 6 7/16" 6 7/16" 6 1/2" 1,800 lb
6340500PL 4" 3 1/16" 10" 10" 8" - 10" 5 9/16" 6 1/2" 6 1/2" 7 1/2" 1,800 lb
5" 3 1/16" 10" 12" 8" - 10" 6 1/8" 7 1/16" 7 3/16" 7 3/16" 1,800 lb
6340800PL 6" 3" 12" 12" 8" - 10" 6 9/16" 7 5/8" 7 5/8" 7 5/8" 1,800 lb
8" 3 1/8" 14" 16" 12" - 14" 7 5/8" 8 15/16" 8 15/16" 8 11/16" 1,800 lb
6341000PL 10" 3 1/16" 16" 18" 16" - 20" 8 7/8" 10 5/16" 10 7/8" 10 3/16" 1,800 lb
6341200PL 12" 3 1/16" 18" 20" 16" - 20" 9 11/16" 9 11/16" 11 3/16" 11 1/16" 5,000 lb
6341400PL 14" 3" 18" 20" 16" - 20" 10 1/4" 10 1/4" 11 11/16" 11 1/8" 5,000 lb
6341600PL 16" 3" 24" - 22" - 24" 11 3/16" 13" - 12 9/16" 7,200 lb
6341800PL 18" 3" 24" - 22" - 24" 12 5/16" 14 1/4" - 13 11/16" 7,200 lb
6342000PL 20" 3" 24" - 22" - 24" 13 1/2" 15 7/16" - 14 15/16" 7,200 lb
6342400PL 24" 3" 30" - 26" - 30" 15 3/8" 18 3/16" - 17 1/8" 7,200 lb
Maximum recommended loads are applicable only when the saddle is used on a flat bearing surface and tack welded to the pipe. When a saddle is used with a pipe roll, the maximum load given for the pipe roll applies to the saddle.
Install in accordance with applicable code.

Pentair, CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH and LENTON are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.

ANSI is a registered trademark of American National Standards Institute.